Fayetteville RC Club

Fox 74
Home
Hat Trick RC
What's New
Guest Book
Fayetteville R/C Club Store
About Fayetteville R/C
Forums and Blogs
Field and Directions
Rules
Bylaws
Becoming a Member
Contact Us
Gallery
Videos
Combat
Tips & Tricks
Fox Engines and Flitelinesolutions
Channel Roster
Links
Mowing Schedule

Fox Eagle .74 Specifications

Bore: 1.00
Stroke: .937
Disp: .736
Weight: 19oz
RPM: 12,700 w 11-8

Significant costs involved in machining the split crankcase used on the earlier Eagle II and III necessitated a change to maintain an acceptable profit margin. Thus, the Eagle IV series was born. This Eagle is a bit more conventional but still retains the separate cylinder casting.

Also new to this series was the introduction of a .74 version. Both the .60 and .74 were once offered in ringed and ABC versions. The .60 still is, but the .74 is now only available with a ring due to significant running and durability problems with the ABC version. Over-compression still tends to be a problem, particularly in earlier Eagle IV engines, and especially the .74. Since it's introduction the .74 has seen at least five head button variations (that we know of) in an attempt to tame handling but problems like finicky needle settings and flameouts may still be experienced. These engines also have a tendency to run too hot. In stock form it is often best to limit the nitro content to 5%. Along with the current head button, and perhaps a Fox Miracle Plug, this may result in acceptable operation. Often, however, more is required and you may consider some of the options that follow. We would also recommend reading the information we have posted on the Eagle .60 since the .74 shares many of the same problems.

Install Current Head Button & Shims
Although the .74 does not respond to this quite as well as the .60, some improvement may be realized by installing the latest head button and, if necessary, further lowering the compression by the addition of shims. Up to two .01" shims may be required. Add shims one at a time and test run! (Shims are available from Fox).

The number of shims required depends upon such things as head button version, propeller size and nitro content. The altitude of the flying site also plays a part. The closer you are to sea level, the more head shims are required. Engines operated at higher altitude sites may run acceptably with no shims at all. We recommend adding no more than two .01" shims. If too many shims are added power will be significantly reduced and/or the engine may not be able to attain a reliable two-stroke setting. As you try to lean the needle it may just quit abruptly. Adding shims also has the undesirable effect of moving the glow plug higher up in the combustion chamber and, if carried too far, can again bring about unexpected "flame-outs". Another side effect is the leaning of the carburetor midrange. While improving MKX series carburetors, this may also aggravate the already overly lean midrange exhibited by some EZ series carburetors and result in additional new problems. Some engines may require a combination of both head shims and carburetor modifications to achieve satisfactory operation.


A Custom Head Button
With the current .74, we also feel there is more to the problem than just compression. The current head button has been opened up to the point that the compression is actually lower than other engines of similar displacement, yet the engine still "acts" like the compression is too high. At first, this seemed to be confirmed by the fact that adding a head shim, or two, often improved the running qualities of the engine, however was not as effective as in the .60 (which has a button of different configuration). We found that the position of the glow plug is also much higher up in the combustion chamber than is normally encountered in engines of this size and suspected this contributed to the unfriendly running qualities. So, after much experimentation, we developed our own head button which we feel is quite successful and really smartens up the .74. It was optimized for 10% nitro at sea level since these were the operating parameters of interest to us. If you posses the necessary machinery and skills you can make one for yourself from the drawing below.

NOTE: This is not just a modification to the stock button, it is made from scratch. Additional shims may or may not be required depending upon your particular operating conditions. Start without them.



* We have found that stock Fox buttons range from about 0.994" to 0.998" For for best performance the button should slip into the liner with a light press fit. We usually custom fit the button to the particular liner it will be used in.


Important Note: Early .74 "ABC" Engines Only!
The very first production run of .74 ABC engines contained cylinder liners and head buttons that differed from all subsequent runs. Since the flange on the cylinder liner was much thinner than later versions, current model head buttons are not compatible. They may contact the piston! Early liners can be identified by measuring the flange as indicated in the following diagram. You may still try adding head shims using the original head button, however we recommend upgrading to the latest (ringed) piston and liner as well as installing a current head button.


Carburetor Related Problems:
On engines equipped with an EZ series carburetor an overly lean upper-midrange often contributes to flameouts and hot running. Many engines are prematurely "cooked" because of this! Please read our page on EZ series carburetors and note the barrel modification. The .74 often requires this modification to run well. The head button problem combined with the carburetor problem can result in a very unfriendly engine! If you do not wish to attempt the modification, install an earlier Fox MKX series carburetor, or a Perry.


Head Clamp Modification:
Another little modification we like to do involves machining the surface of the head clamp where it contacts the head button. The head clamp casting tends to be quite rough and/or porous which reduces the surface area contacting the head button. We have seen quite a number of engines with a layer of baked on castor in between the top of the head button and the head clamp. Machining this surface allows full contact to further aid cooling. Although only a very small amount of material will be removed, we also recommend removing an equal amount from the bottom of the head clamp. This will ensure that the head clamp does not contact the cylinder casting before the head button is properly secured.


Some recent problems:
There are new problems showing up in more recent engines. These are related to a combination of the EZ carburetor and a modification to the crankcase. The crankcase has been modified internally to include a thin slot that runs between the carb. intake and front bearing. The intent was for the intake vacuum to prevent fuel from leaking past the front bearing while the engine is running. Unfortunately, in some cases, too much air is also drawn in through the slot upsetting the mixture. (This is basically an air leak!). The air-bleed EZ series carburetor may not have the adjustment range to compensate for this, resulting in the inability to achieve a proper mixture adjustment. Often the engine will run poorly in the low to mid-throttle range although some engines suck in enough air that they run poorly over the entire throttle range. The engine need not be disassembled to check for the presence of the slot, just remove the carburetor and the end of the slot is visible as shown in this photo

We have been filling the slot with JB weld to fix the air leak problem, but this must be done carefully so that the operation of the crankshaft is not impeded. The engine must be disassembled, then remove the front bearing and clean the crankcase thoroughly with solvent. Carefully fill the slot (using a toothpick, etc.) trying not to get too much excess. Allow the JB weld to set for a while, but not fully cure, then insert the crankshaft. The front edge of the crankshaft will neatly scrape away the excess JB weld for a perfect fit. Allow the JB weld to cure fully before installing the front bearing and re-assembling the engine.

An Important Final Note:
It is important that your engine still be in good condition before employing any of these modifications. The tendency to run hot can result in an engine that is ruined in very few flights as the frustrated pilot tries over and over again to get a complete flight without a flameout. Your Eagle .74 should have strong, snappy, compression when you flip it over. If this is no longer the case, you will likely need a rebuild first. The custom head button, or shims, cannot be expected to cure a worn or damaged engine.

Fayetteville RC Club
AMA Silver Leader
#680